聯通d400-lh的盒子，海信ip906h同款

jarod_x · 發表于 2017-5-16 17:25

直接用串口線，停止不動

HELLO! BOOT0 is starting!
boot0 version : 4.2.0
fel_flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.8
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 576 MHz
DRAM zq value: 003b3bfb
READ DQS LCDL = 00212122
DRAM SIZE =1024 M
odt delay
dram size =1024
card boot number = 2
card no is 2
sdcard 2 line count 8
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 2***
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 cmd 8 err 00000100
[mmc]: mmc 2 send if cond failed
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 cmd 55 err 00000100
[mmc]: mmc 2 send app cmd failed
[mmc]: ***Try MMC card 2***
[mmc]: 8bit ddr!!!
[mmc]: MMC ver 5.0
[mmc]: SD/MMC Card: 8bit, capacity: 3776MB
[mmc]: vendor: Man 00110100 Snr 00629b44
[mmc]: product: 004GE
[mmc]: revision: 3.0
[mmc]: ***SD/MMC 2 init OK!!!***
sdcard 2 init ok
The size of uboot is 000dc000.
sum=d4ed32bc
src_sum=d4ed32bc
set_mmc_para,sdly 50M 0
set_mmc_para,sdly 25M 0
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
SUNXI_NORMAL_MODE
[    0.264]e mode

U-Boot 2011.09-rc1 (Jun 23 2016 - 11:10:30) Allwinner Technology

[    0.271]version: 1.1.0
normal mode
[    0.279]pmbus: ready
not set main pmu id
axp_probe error
[    0.316]PMU: pll1 1008 Mhz,PLL6=600 Mhz
AXI=336 Mhz,AHB=200 Mhz, APB1=100 Mhz
sid read already
fel key new mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
normal mode
[    0.347]DRAM:  1 GiB
relocation Offset is: 35af6000
[box standby] read rtc = 0x0
[box_start_os] mag be start_type no use
user_gpio config
user_gpio ok
gic: normal or no secure os mode
workmode = 0
MMC:    2
[    0.426][mmc]: mmc driver ver 2016-03-24 19:30:15
[    0.431][mmc]: get sdc_phy_wipe fail.
[    0.435][mmc]: get sdc0 sdc_erase fail.
[    0.439][mmc]: get sdc_2xmode ok, val = 1
[    0.443][mmc]: get sdc_ddrmode ok, val = 1
[    0.447][mmc]: get sdc_f_max fail,use default  50000000Hz
[    0.453][mmc]: get card_line ok, card_line = 8
[    0.457][mmc]: get sdc_ex_dly_used fail,use default
[    0.462][mmc]: SUNXI SD/MMC: 2
[    0.467][mmc]: mmc_config_clock: clk 400000
[    0.482][mmc]: *Try SD card 2*
[    0.487][mmc]: mmc 2 cmd 8 err 100
[    0.493][mmc]: mmc send if cond failed
[    0.498][mmc]: mmc 2 cmd 55 err 100
[    0.504][mmc]: send app cmd failed
[    0.507][mmc]: *Try MMC card 2*
[    0.570][mmc]: mmc_config_clock: clk 25000000
[    0.584][mmc]: mmc re-update_phase
[    0.591][mmc]: mmc re-update_phase
[    0.598][mmc]: mmc re-update_phase
[    0.603][mmc]: ddr8
[    0.607][mmc]: mmc re-update_phase
[    0.614][mmc]: mmc_config_clock: clk 25000000
[    0.624][mmc]: mmc_config_clock: clk 50000000
[    0.632][mmc]: CID 0x11010030 0x30344745 0x3000629b 0x44bf62a5
[    0.637][mmc]: MMC ver 5.0
[    0.640][mmc]: mmc clk 50000000
[    0.643][mmc]: SD/MMC Card: 8bit, capacity: 3776MB
[    0.648][mmc]: boot0 capacity: 2000KB,boot1 capacity: 2000KB
[    0.654][mmc]: ***SD/MMC 2 init OK!!!***
[    0.660][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte
[    0.666][mmc]: secure_feature 0x55
[    0.669][mmc]: secure_removal_type  0x9
[    0.673]sunxi flash init ok
script config pll_de to 864 Mhz
Not Found clk pll_video1 in script
script config pll_video to 297 Mhz
[boot]disp_init_tv
[DISP_TV] disp_init_tv enter g_tv_used
screen 0 do not support TV TYPE!
[BOOOT_DISP_TV] disp tv device_registered
unable to find regulator vcc-hdmi-18 from [pmu1_regu] or [pmu2_regu]
enable power vcc-hdmi-18, ret=-1
DRV_DISP_Init end
error: open tv_vdid.fex, maybe it is not exist
save_vendor_id=,value = 0
read byte = 10
[get_display_resolution] = 409
read byte = 10
[get_display_resolution] = 20b
boot_disp.auto_hpd=1
auto hpd check has 100 times!
auto check no any connected, the output_type is 2
attched ok, mgr1<-->device1, type=2, mode=11----
ready to set mode
disp_tv_enable
[    2.090]finally, output_type=0x2, output_mode=0xb, screen_id=0x1, disp_para=0x20b0000
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:14-
-name-       -start-    -size-
bootloader  : 1000000    1000000
env       : 2000000    1000000
boot       : 3000000    1000000
system    : 4000000    30000000
misc       : 34000000    1000000
recovery : 35000000    2000000
sysrecovery : 37000000    30000000
private    : 67000000    1000000
Reserve0 : 68000000    1000000
klog       : 69000000    1000000
Reserve1 : 6a000000    2000000
Reserve2 : 6c000000    1000000
cache    : 6d000000    28000000
UDISK    : 95000000    0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_mmc
key 0
cant find rcvy value
cant find fstbt value
misc partition found
to be run cmd=run setargs_mmc boot_normal
read item0 copy0
Item0 (Map) magic is bad
the secure storage item0 copy0 is bad
read item0 copy1
Item0 (Map) magic is bad
the secure storage item0 copy0 == copy1, the data is good
the secure storage map is empty
no item name mac in the map
sunxi storage read fail
no item name wifi_mac in the map
sunxi storage read fail
no item name bt_mac in the map
sunxi storage read fail
no item name specialstr in the map
sunxi storage read fail
no item name serialno in the map
sunxi storage read fail
check user data form private
updataed mac = AC:4A:FE:7D:FE:26
updataed specialstr = 00490100000011D400LH011542003519
WORK_MODE_BOOT
adver not need show
sunxi_bmp_logo_display
f_read btr over hd12896
read byte = 3686456
[    2.336]screen_id =1, screen_width =720, screen_height =576
[    2.341]frame buffer address 46400036
[    2.345]Hit any key to stop autoboot:  0
read boot or recovery all
[    2.506]sunxi flash read :offset 3000000, 12924599 bytes OK
[    2.514]ready to boot
board_display_setenv:  disp_para=20b0000 init_disp=20b0409 tv_vdid=0
[    2.523][mmc]: mmc exit start
[    2.527][mmc]: mmc_config_clock: clk 50000000
[    2.537][mmc]: mmc_config_clock: clk 400000
[    2.552][mmc]: mmc 2 cmd 8 err 100
[    2.558][mmc]: mmc send if cond failed
[    2.563][mmc]: mmc 2 cmd 55 err 100
[    2.569][mmc]: send app cmd failed
[    2.598][mmc]: get sdc_phy_wipe fail.
[    2.602][mmc]: get sdc0 sdc_erase fail.
[    2.606][mmc]: get sdc_2xmode ok, val = 1
[    2.610][mmc]: get sdc_ddrmode ok, val = 1
[    2.614][mmc]: get sdc_f_max fail,use default  50000000Hz
[    2.620][mmc]: get card_line ok, card_line = 8
[    2.624][mmc]: get sdc_ex_dly_used fail,use default
[    2.629][mmc]: mmc 2 exit ok
[    2.632]
Starting kernel ...

[sun8i_fixup]: From boot, get meminfo:
      Start:  0x40000000
      Size: 1024MB
ion_carveout reserve: 160m@0 312m@0 130m@1 200m@1
ion_reserve_common: ion reserve: [0x4c800000, 0x60000000]!

曾俊虎 · 發表于 2023-6-26 16:25

？？？？

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚