四川B860A ZTV801113P0007 磚了怎么救

hep08 · 發表于 2017-1-14 21:19

固件版本為ZTV801113P0007
對應機頂盒硬件版本為IBHR-ANDROIDSTBGA-068
Recovery版本V801014
Uboot：V0025
配置版本：V20150624
logo v801006
根據網上的一鍵ROOT方法用ABD進行破解，結果機頂盒成磚了，只停在啟動界面，后來在網上找了教程如下
必須找到這三個文件
ota.zip
u-boot-aml-ucl.bin
uImage_recovery

參照什么的方法TTL分別刷入，指令：
m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
m8m2_n200_v1#sdc_update recovery uImage_recovery

重新啟動盒子
m8m2_n200_v1#safe 這個不很重要，否則會提示錯誤not defined
完成之后提示符變?yōu)?重新刷的話按回車+ctrl鍵多次進入#
#recovery --update_package=/sdcard/ota.zip

但這個方法也不行，后來試了在OTA.ZIP中解包出 recovery.img 和 system.img 放在SD中輸入以下兩個命令也不行。
sdc_update recovery recovery.img恢復recovery,
還可以sdc_update system system.img

請問有高手嗎，怎么解決這個問題。我以前備份了的ota.zip
u-boot-aml-ucl.bin
uImage_recovery 這三個文件。

hep08 · 發表于 2017-1-14 21:24

現在盒子不斷重啟，提示發現新軟件正在升級 請勿斷電

billking · 發表于 2017-1-14 21:27

建議參考這個方法http://ktgpgw.cn/tv-581030-1-2.html

hep08 · 發表于 2017-1-14 21:47

試了顯示 Unable to read "recovery.img" from mmc 0:1

hep08 · 發表于 2017-1-14 21:48

m8m2_n200_v1#
m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
sdio_detect return 1
[mmc_init] SDIO Port B:0, if_type=7, initialized OK!
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0x71690B[0M]
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0xee15d177
      u-boot-aml-ucl.bin is exist
msg:Down(store) part(bootloader) sz(0x71690) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 8
fat:Filesize is 0x71690B[0M]
fat:sz 0x690 gz 0x1690, bps 0x1000
msg:Burn Start...
msg:Acs not in the spl of uboot_bin
mmc switch part boot0 success
mmc switch part boot1 success
mmc switch part user success
msg:Burn complete
BURN u-boot-aml-ucl.bin to part bootloader OK!
=====>Burn part bootloader in fmt normal OK<======

m8m2_n200_v1#sdc_update bootloader u-boot-aml-ucl.bin
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0x71690B[0M]
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0xee15d177
      u-boot-aml-ucl.bin is exist
msg:Down(store) part(bootloader) sz(0x71690) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 8
fat:Filesize is 0x71690B[0M]
fat:sz 0x690 gz 0x1690, bps 0x1000
msg:Burn Start...
msg:Acs not in the spl of uboot_bin
mmc switch part boot0 success
mmc switch part boot1 success
mmc switch part user success
msg:Burn complete
BURN u-boot-aml-ucl.bin to part bootloader OK!
=====>Burn part bootloader in fmt normal OK<======

m8m2_n200_v1#sdc_update recovery uImage_recovery
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
fat:Filesize is 0xb42fc0B[11M]
ERR(v2_common/optimus_simg2img.c)L60:sparse bad magic, expect 0xed26ff3a but 0x52444e41
      uImage_recovery is exist
msg:flash LOGIC partCap 0x1400000B
msg:Down(store) part(recovery) sz(0xb42fc0) fmt(normal)
msg:totalSlotNum = 0, nextWriteBackSlot 1
fat:Filesize is 0xb42fc0B[11M]
msg:Burn Start...
fat:sz 0xfc0 gz 0x2fc0, bps 0x1000
msg:Burn complete
BURN uImage_recovery to part recovery OK!
=====>Burn part recovery in fmt normal OK<======

m8m2_n200_v1#run recovery --update_package=/sdcard/ota.zip
enter recovery
Device: SDIO Port B
Manufacturer ID: 0
OEM: 0
Name: ran Speed: 20000000
Rd Block Len: 512
SD version 2.0
High Capacity: Yes
Capacity: 3941597184
Boot Part Size: 0
Bus Width: 4-bit
reading recovery.img

** Unable to read "recovery.img" from mmc 0:1 **
[imgread]Secure kernel sz 0xb42fc0
Aml log : M8-R1024 IMG pass!

hep08 · 發表于 2017-1-15 13:56

請問哪位大神用什么方法解決

hep08 · 發表于 2017-1-15 15:37

#
# recovery --update_package=/sdcard/ota.zip
I:loaded /etc/recovery.kl
I:recovery key map table
I:=========================
I:  0 type:select value:-4 key:28 15 158 -1 -1 -1
I:  1 type:down value:-3 key:108 114 109 -1 -1 -1
I:  2 type:up value:-2 key:103 104 115 -1 -1 -1
I:  3 type:back_door value:-6 key:128 26 118 -1 -1 -1
I:
enter recovery mode,run green led!
Language ==> Not found
MarketCode ==> Not found
OperatorsCode ==> Not found
E:market_code =-1
E:operators_code =-1
gr_init_font  222: cwidth 32  cheight35
can't open /dev/tty0: No such file or directory
framebuffer: fd 3 (1920 x 1080)
   installing_text:  (1 x 1 @ 1896)
      erasing_text:  (1 x 1 @ 1599)
   no_command_text:  (1 x 1 @ 1599)
         error_text:  (1 x 1 @ 1599)

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[LEDCtrlRun]@@@@@=====>LEDCTRL_RUN_GREEN_OFF !

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[LEDCtrlRun]@@@@@=====>LEDIR_IOCS_OFF !

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[LEDCtrlLink]@@@@@=====>LEDIR_IOCS_OFF !

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[LEDCtrlLink]@@@@@=====>LEDIR_IOCS_OFF !

[CheckLEDDevForCtrl]XIEZHIJUN CheckLEDDevForCtrl

[LEDCtrlRun]@@@@@=====>LEDCTRL_RUN_GREEN_ON !
UpdateMode ==> Not found
發現新版軟件,正在升級,勿斷電,請稍候！
[ 9.203992@0] EXT4-fs error (device mmcblk1p9): ext4_validate_block_bitmap:368: comm recovery: bg 4: block 131072: invalid block bitmap
[ 9.204895@0] Aborting journal on device mmcblk1p9-8.
[ 9.205705@0] EXT4-fs (mmcblk1p9): Remounting filesystem read-only
[ 9.210732@2] Restarting system from safe_mode.
[ 9.212590@2] Restarting Linux version 3.10.33-svn48455 (yinjiandong@A23131934) (gcc version 4.7.3 20130205 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.02-01-20130221 - Linaro GCC 2013.02) ) #1 SMP PREEMPT Fri Oct 9 21:30:38 CST 2015
[ 9.212590@2]
[ 9.262540@2] arm_restart: Console was locked! Busting

QA9:A;SVN:74E;POC:17F;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
從這上面開始進行重啟了。
更新出現 這樣有誰能幫忙啊

jjjian · 發表于 2017-1-16 07:09

IBHR-ANDROIDSTBGA-068是高安版
那三個文件是從自己的盒子里備份的嗎？

hep08 · 發表于 2017-1-22 19:47

是的

roweson · 發表于 2017-1-23 22:38

我的四川的,也是你那咱問題,直接卡刷system.img就行了.必須TTL

› 運營商IPTV / 有線電視 / 廣電機頂盒 › 中興機頂盒

四川B860A ZTV801113P0007 磚了 怎么救

四川B860A ZTV801113P0007 磚了 怎么救

四川B860A ZTV801113P0007 磚了怎么救

四川B860A ZTV801113P0007 磚了怎么救