魔百盒 cm311-1sa-ch刷磚卡開機logo求解決辦法
已經刷了無數個版本了，雙鉤也不行，直接第二個會動畫的畫面卡哪里了，下面是跑碼結果。求高手指點下
跪謝
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180
TE: 70961
BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz
Board ID = 8
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 8
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz
dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
soc_VRef_reg_value 0x 00000021 00000022 00000022 00000023 00000024 00000021 00000021 00000023 00000021 00000021 00000023 00000022 00000022 00000021 00000022 00000022 00000022 00000023 00000021 00000020 00000022 00000022 00000020 00000023 00000022 00000023 00000022 00000024 00000024 00000021 00000023 00000022 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
dram_vref_reg_value 0x 00000060
2D training succeed
auto size-- 65535DDR cs0 size: 1024MB
DDR cs1 size: 1024MB
DMC_DDR_CTRL: 00e0001bDDR size: 2048MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 420
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000dce00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 31 20 00 00 17 37 38 38 57 48 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE: BL31: v1.3(release):ec7984eef
NOTICE: BL31: Built : 15:24:59, Nov 30 2020
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01-g23d25cc-dirty (Dec 02 2021 - 16:22:46)
DRAM: 2 GiB
Relocation Offset is: 76e39000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
gpio: pin GPIOAO_10 (gpio 10) value is 1
register usb cfg[0][1] = 0000000077f36d70
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 fe ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 fe ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x0000000073e29db0
aml_priv->desc_buf = 0x0000000073e2c0f0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073e2e940,dt_addr=0000000073e2e940
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000060000000 1
14: product 0000000008000000 1
15: cache 0000000050000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x57400000
In: serial
Out: serial
Err: serial
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 44bbcb93, store 44bbcb93
_verify_dtb_checksum()-3476: calc 44bbcb93, store 44bbcb93
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 634
aml_config_dtb 664
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = "
??"
status = "disabled"
status = "okay"
Net: dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
upgrade_step=2
aml log : internal sys error!
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
6220854 bytes read in 186 ms (31.9 MiB/s)
[imgread]load bmp from ext4 part okay
bmp pixel: 24
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[1080p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 16
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 6 vid_clk_div = 1
hdmitx: set enc for VIC: 16
hdmitx phy setting done
rx version is 1.4 or below div=10
hdmtix: set audio
hdmi_tx_set: save mode: 1080p60hz, attr: 444,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x57400000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 1
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
console=1
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[oemkey] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[cmei] not programed yet
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
console=1
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[oemkey] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[cmei] not programed yet
time_out = 7a120
key[0] = 7d82dd22
key[1] = 7e81dd22
key[2] = 728ddd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
time_out = 2625a0
key[0] = e31cfb04
key[1] = b748fb04
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
pll tsensor avg: 0x1eae, u_efuse: 0x8000
temp1: 28
ddr tsensor avg: 0x1ee2, u_efuse: 0x8054
temp2: 28
device cool done
CONFIG_SYSTEM_AS_ROOT: null
system_mode: 0
Start read misc partition datas!
info->magic =
info->version_major = 1
info->version_minor = 0
info->slots[0].priority = 15
info->slots[0].tries_remaining = 7
info->slots[0].successful_boot = 0
info->slots[1].priority = 14
info->slots[1].tries_remaining = 7
info->slots[1].successful_boot = 0
info->crc32 = -1075449479
active slot = 0
CONFIG_AVB2: null
active_slot: normal
avb2: 0
ee_gate_off ...
avb2: 0
## Booting Android Image at 0x01080000 ...
Kernel command line: androidboot.dtbo_idx=0 buildvariant=userdebug
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
Amlogic multi-dtb tool
Single dtb detected
find 1 dtbos
dtbos to be applied: 0
Apply dtbo 0
Loading Kernel Image(COMP_NONE) ... OK
kernel loaded at 0x01080000, end = 0x01a09238
Loading Ramdisk to 09e92000, end 09fff37a ... OK
Loading Device Tree to 0000000009e7a000, end 0000000009e91063 ... OK
fdt_fixup_memory_banks, reg:0000000000000000
fdt_instaboot: no instaboot image
Starting kernel ...
uboot time: 5710186 us
[ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000
[ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000@0] 7f800000 - 80000000, 8192 KB, linux,meson-fb
[ 0.000000@0] 77800000 - 7f800000, 131072 KB, linux,ion-dev
[ 0.000000@0] 73400000 - 77800000, 69632 KB, linux,di_cma
[ 0.000000@0] 5a400000 - 73400000, 409600 KB, linux,codec_mm_cma
[ 0.000000@0] 5a400000 - 5a400000, 0 KB, linux,codec_mm_reserved
[ 0.000000@0] 59000000 - 5a400000, 20480 KB, linux,vdin1_cma
[ 11.674783@1] init: Failed to mount required partitions early ...
[ 11.675307@1] pgd = edc24000
[ 11.678141@1] [00000014] *pgd=580b9835
[ 11.800169@0] reboot: Restarting system with command 'bootloader'
bl31 reboot reason: 0xd
bl31 reboot reason: 0x7
system cmd 1.
G12A:BL:0253b8:61aa2d;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f83180
TE: 66758
BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz
Board ID = 8
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 8
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz
dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
soc_vref_reg_value 0x 00000021 00000022 00000023 00000022 00000025 00000022 00000022 00000023 00000021 00000021 00000023 00000023 00000022 00000022 00000022 00000022 00000022 00000023 00000021 00000020 00000021 00000022 00000020 00000023 00000022 00000023 00000022 00000024 00000024 00000021 00000023 00000021 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
dram_vref_reg_value 0x 00000060
2D training succeed
auto size-- 65535DDR cs0 size: 1024MB
DDR cs1 size: 1024MB
DMC_DDR_CTRL: 00e0001bDDR size: 2048MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
non-sec scramble use zero key
ddr scramble enabled
100bdlr_step_size ps== 429
result report
boot times 1Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000dce00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0c 70 00 01 31 20 00 00 17 37 38 38 57 48 50
[0.869824 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE: BL31: v1.3(release):ec7984eef
NOTICE: BL31: Built : 15:24:59, Nov 30 2020
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01-g23d25cc-dirty (Dec 02 2021 - 16:22:46)
DRAM: 2 GiB
Relocation Offset is: 76e39000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
gpio: pin GPIOAO_10 (gpio 10) value is 1
register usb cfg[0][1] = 0000000077f36d70
NAND: get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 fe ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 fe ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC: aml_priv->desc_buf = 0x0000000073e29db0
aml_priv->desc_buf = 0x0000000073e2c0f0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
start dts,buffer=0000000073e2e940,dt_addr=0000000073e2e940
get_partition_from_dts() 92: ret 0
Amlogic multi-dtb tool
Single dtb detected
parts: 17
00: logo 0000000000800000 1
01: recovery 0000000001800000 1
02: misc 0000000000800000 1
03: dtbo 0000000000800000 1
04: cri_data 0000000000800000 2
05: param 0000000001000000 2
06: boot 0000000001000000 1
set has_boot_slot = 0
07: rsv 0000000001000000 1
08: metadata 0000000001000000 1
09: vbmeta 0000000000200000 1
10: tee 0000000002000000 1
11: vendor 0000000014000000 1
12: odm 0000000008000000 1
13: system 0000000060000000 1
14: product 0000000008000000 1
15: cache 0000000050000000 2
16: data ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x57400000
In: serial
Out: serial
Err: serial
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 44bbcb93, store 44bbcb93
_verify_dtb_checksum()-3476: calc 44bbcb93, store 44bbcb93
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
Multi dtb tool version: v2 .
Support 4 dtbs.
aml_dt soc: g12a platform: u212 variant: 2g
dtb 0 soc: g12a plat: u212 vari: 1g
dtb 1 soc: g12a plat: u212 vari: 2g
dtb 2 soc: g12a plat: u212 vari: 3g
dtb 3 soc: sm1 plat: ac213 vari: 2g
Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 634
aml_config_dtb 664
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = "
??"
status = "disabled"
status = "okay"
Net: dwmac.ff3f0000amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
upgrade_step=2
aml log : internal sys error!
reboot_mode:::: bootloader
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
6220854 bytes read in 185 ms (32.1 MiB/s)
[imgread]load bmp from ext4 part okay
bmp pixel: 24
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,1919,0,1079
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[1080p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 16
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 6 vid_clk_div = 1
hdmitx: set enc for VIC: 16
hdmitx phy setting done
rx version is 1.4 or below div=10
hdmtix: set audio
hdmi_tx_set: save mode: 1080p60hz, attr: 444,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x57400000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 1
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
console=1
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[KM]Error:f[key_manage_query_size]L515:key[oemkey] not programed yet
[KM]Error:f[key_manage_query_size]L515:key[cmei] not programed yet
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
time_out = 7a120
key[0] = 7d82dd22
key[1] = 7e81dd22
key[2] = 728ddd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
time_out = 2625a0
key[0] = e31cfb04
key[1] = b748fb04
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10
Usage:
irkey - No additional help available.
g12a_u212_v1#
|
網站導航
發表于 2024-12-11 14:55
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 