這玩意但凡線刷個不是官改的固件都死給你看，都是uboot/獲取返回/diskinitial命令出錯，怎么搞啊
TTL日志：
- U-Boot 2015.01-g7ec51b9-dirty (Nov 24 2016 - 21:44:53)
- DRAM: 1 GiB
- Starting uboot
- gpio: pin GPIOCLK_1 (gpio 99) value is 1
- gpio: pin GPIOAO_6 (gpio 106) value is 1
- [MSG]MMC init in usb
- aml_priv->desc_buf = 0x0000000037ec6db0
- aml_priv->desc_buf = 0x0000000037ec8f40
- SDIO Port B: 0, SDIO Port C: 1
- Try USB burn
- Set Addr 19
- Get DT cfg
- Get DT cfg
- Get DT cfg
- Get DT cfg
- Get DT cfg
- set CFG
- ID[16]
- tplcmd[ echo 12345]
- 12345
- [MSG]ret = 0
- [info]success
- BULKcmd[ low_power]
- [info]success
- ID[16]
- tplcmd[ download mem dtb normal 256000]
- [MSG]Down(mem) part(dtb) sz(0x3e800) fmt(normal)
- [MSG]totalSlotNum = 0, nextWriteBackSlot 4
- [info]success
- [MSG]Burn Start...
- [MSG]load dt.img to 0x0000000001000000, sz=0x3e800
- [MSG]Burn complete
- BULKcmd[download get_status]
- [info]success
- BULKcmd[disk_initial 1]
- Amlogic multi-dtb tool
- Multi dtb detected
- checkhw - ADC value:0x8
- Multi dtb tool version: v2 .
- Support 7 dtbs.
- aml_dt soc: gxl platform: p211 variant: 1g
- dtb 0 soc: gxb plat: p200 vari: 1g
- dtb 1 soc: gxb plat: p200 vari: 2g
- dtb 2 soc: gxl plat: p211 vari: 1g
- dtb 3 soc: gxl plat: p211 vari: 2g
- dtb 4 soc: gxl plat: p215 vari: 1g
- dtb 5 soc: gxl plat: p215 vari: 2g
- dtb 6 soc: gxl plat: p215hc100 vari: 2g
- Find match dtb: 2
- start dts,buffer=0000000001000000,dt_addr=0000000001011800
- parts: 11
- 00: conf 0000000000400000 1
- 01: logo 0000000002000000 1
- 02: recovery 0000000002000000 1
- 03: rsv 0000000000800000 1
- 04: tee 0000000000800000 1
- 05: crypt 0000000002000000 1
- 06: misc 0000000002000000 1
- 07: boot 0000000002000000 1
- 08: system 0000000040000000 1
- 09: cache 0000000030000000 2
- 10: data ffffffffffffffff 4
- emmc/sd response timeout, cmd = 8
- emmc/sd response timeout, cmd = 55
- emmc/sd response timeout, cmd = 1
- card out
- emmc/sd response timeout, cmd = 8
- emmc/sd response timeout, cmd = 55
- emmc/sd response timeout, cmd = 1
- amlmmc cmd failed
- store - STORE sub-system
- Usage:
- store store init flag
- store read name addr off|partition size
- read 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store write name addr off|partition size
- write 'size' bytes starting at offset 'off'
- to/from memory address 'addr', skipping bad blocks.
- store rom_write add off size.
- write uboot to the boot device
- store erase boot/data:
- erase the area which is uboot or data
- store erase dtb
- store erase key
- store rom_protect on/off
- store scrub off|partition size
- scrub the area from offset and size
- store dtb iread/read/write addr <size>
- read/write dtb, size is optional
- store key read/write addr <size>
- read/write key, size is optional
- cmd [store] init failed
- [info]failed:
|
網站導航
發表于 2023-2-6 23:11
收藏
淘帖
頂一個
踩
提升卡
置頂卡
變色卡
千斤頂
樓主
znds.com 