ZNDS智能電視網 推薦當貝市場

TV應用下載 / 資源分享區

軟件下載 | 游戲 | 討論 | 電視計算器

綜合交流 / 評測 / 活動區

交流區 | 測硬件 | 網站活動 | Z幣中心

新手入門 / 進階 / 社區互助

新手 | 你問我答 | 免費刷機救磚 | ROM固件

查看: 12635|回復: 2
上一主題 下一主題
[求助]

8726mx命令怎么使用

[復制鏈接]
跳轉到指定樓層
樓主
發表于 2021-3-30 19:26 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式 | 來自廣西
本帖最后由 xhm789 于 2021-3-30 20:05 編輯

電視進不了桌面,想重u盤裝。

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES aLGorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system


8726(1).txt

10.22 KB, 下載次數: 2, 下載積分: 金幣 -1


上一篇:江蘇移動魔百和HG680-KA點擊版本信息沒用的前提...
下一篇:CM201-2 YS已成磚,如何救磚,請大俠指教!
沙發
 樓主| 發表于 2021-3-30 20:03 | 只看該作者 | 來自廣西

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system
回復 支持 反對

使用道具 舉報

板凳
 樓主| 發表于 2021-3-30 20:04 | 只看該作者 | 來自廣西

EC3_MX_PANEL_V6 #?
?       - alias for 'help'
adtask  - Ad task when time is not boot time it will sleep
aeschk  - aeschk AES algorithm check sub-system
autoping- do auto ping test
autoscr - run script from memory
base    - print or set address offset
bdinfo  - print Board Info structure
bmp     - manipulate BMP image data
boardid_prefetch- boardid sub-system
boot    - SPI-NAND-COMPATIBLE
bootc   - boot boot.img form sdcard
bootm   - boot application image from memory
bootn   - boot uImage form nand
bootp   - boot image via network using BOOTP/TFTP protocol
bootr   - boot uImage_recovery from sdcard
bootu   - boot uImage form sdcard
burnuboot- burn uboot form sdcard
calc    - command for calculate
cbusreg - cbus register read/write
chpart  - change active partition
clear_rebootmode- clear rebootmode
clkmsr  - measure PLL clock
cmp     - memory compare
coninfo - print console devices and information
cp      - memory copy
crc32   - checksum calculation
data    - SPI-NAND-COMPATIBLE || SPI-NAND-EMMC-COMPATIBLE
dcache  - enable or disable data cache
defenv  - default environment
defenv_without- defenv without environment variables
dhcp    - boot image via network using DHCP/TFTP protocol
dummy   - Customer defined command!
echo    - echo args to console
editenv - edit environment variable
efuse   - efuse version/licence/mac/hdcp/usid read/write or dump raw efuse data commands
env     - environment handling commands
ethchk  - check ethernet status
ethdbg  - set ethernet debug level
ethmode - set ethernet mac mode
ethrst  - reset ethernet phy
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
false   - do nothing, unsuccessfully
fatexist- find the file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
get_img_size- get img size and save the result as a environment variable
get_rebootmode- get reboot mode
go      - start application at address 'addr'
hdcp    - HDCP sub-system
help    - print command description/usage
icache  - enable or disable instruction cache
imxtract- extract a part of a multi-image
init_wifi- init wifi power
irkey   - irkey key_value time_value
itest   - return true/false on integer compare
kgdb    - enter gdb remote debug mode
ledflicker- Led flicker when there is no uImage or recovery can run
loadb   - load binary file over serial line (kermit mode)
loadenv - load environment at address 'addr'
loads   - load S-Record file over serial line
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
macreg  - ethernet mac register read/write/dump
md      - memory display
mdc_clk - do mdc clock
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
msleep  - delay execution for some time
mtdparts- define flash/nand partitions
mtest   - simple RAM read/write test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
netspd_f- enforce eth speed
nm      - memory modify (constant address)
phyreg  - ethernet phy register read/write/dump
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saradc  - saradc sub-system
saveenv - save environment variables to persistent storage
secukey - security KEY sub-system
setenv  - set environment variables
sf      - SPI flash sub-system
showvar - print local hushshell variables
sleep   - delay execution for some time
source  - run script from memory
ssecukey- NAND KEY sub-system
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
tiny_usbtool- start tiny USB tool for PC burner
true    - do nothing, successfully
unpackimg- unpack imgpack to single
usb     - USB sub-system
usbbc   - test usb bc
usbboot - boot from USB device
usid_prefetch- usid sub-system
uuid_prefetch- uuid sub-system
version - print monitor, compiler and linker version
video   - video sub-system
回復 支持 反對

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 立即注冊

本版積分規則

Archiver|新帖|標簽|軟件|Sitemap|ZNDS智能電視網 ( 蘇ICP備2023012627號 )

網絡信息服務信用承諾書 | 增值電信業務經營許可證:蘇B2-20221768 丨 蘇公網安備 32011402011373號

GMT+8, 2024-9-27 21:19 , Processed in 0.058646 second(s), 13 queries , Redis On.

Powered by Discuz!

監督舉報:report#znds.com (請將#替換為@)

© 2007-2024 ZNDS.Com

快速回復 返回頂部 返回列表