中興B860AV1.1-T接CH340G小板連ttl遇到的問題

renyyren · 發表于 2018-3-20 22:20

本帖最后由 renyyren 于 2018-3-24 16:17 編輯

從閑魚淘了個江蘇版的中興B860AV1.1-T，用密碼計算器算密碼打開了ADB，安裝了沙發**，可是在使用中總是彈出網絡檢查失敗之類的問題，并且第三方應用不能更新。就從網上買了塊CH340G的USB轉TTL模塊?？墒墙裉焓盏胶?，卻遇到了新問題。請教大神怎么破？
盒子固件版本
中興B860AV1.1-T接CH340G小板連ttl遇到的問題

打開ABD,安裝部分應用后不能繼續安裝第三方應用
中興B860AV1.1-T接CH340G小板連ttl遇到的問題

設置

跑碼遇到的問題
中興B860AV1.1-T接CH340G小板連ttl遇到的問題

跑碼到這里就不能繼續操作了
~~~~~~~~GXL:BL1:9ac50e:a1974b;FEAT:ADFD318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 178161
BL2 Built : 15:54:04, Mar  2 2017.
gxl ge99b2a5 - xiaobo.gu@droid05
Board ID = 8, adc=614
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
Can't match board id, use default ddr_set[0]
DDR type: DDR3-ID
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x0009f000
NOTICE:  BL3-1: v1.0(debug):5f10d2b
NOTICE:  BL3-1: Built : 15:00:19, Mar  7 2017
aml log : bl31 normal boot !
[Image: gxl_v1.1.3089-661026e 2017-01-10 18:34:56 qiufang.dai@droid07]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = e2
efuse init hdcp = c, cf9=7
[0.630496 Inits done]
sINFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
ecur
t
5aUs-kB osOTTa r2t0!1
r.0hi1g-hg 8tea9s1kb 5st6a r(tA!p
: 2lo7w  2t0a1s7k  -s t1a5r:t5!5
48)
DRAM:  1 GiB
Starting uboot
gpio: pin GPIOCLK_1 (gpio 99) value is 1
gpio: pin GPIOAO_6 (gpio 106) value is 1
register usb cfg[0][1] = 000000003ff5d148
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
aml_priv->desc_buf = 0x000000003bec1db0
aml_priv->desc_buf = 0x000000003bec3f40
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd = 8
emmc/sd response timeout, cmd = 55
[mmc_init] mmc init success
mmc read lba=0x14000, blocks=0x400
   Amlogic multi-dtb tool
   Multi dtb detected
   unified board, board id = 8
CONFIG_4LAYERS_BOARD_ID_1  8  12 size: 0x40000000,
   Multi dtb tool version: v2 .
   Support 7 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxb plat: p200 vari: 1g
      dtb 1 soc: gxb plat: p200 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
      dtb 6 soc: gxl plat: p215hc100 vari: 2g
   Find match dtb: 2
start dts,buffer=000000003bec6740,dt_addr=000000003bed7f40
parts: 11
00:    conf 0000000000400000 1
01:    logo 0000000002000000 1
02:  recovery 0000000002000000 1
03:    rsv 0000000000800000 1
04:    tee 0000000000800000 1
05:    crypt 0000000002000000 1
06:    misc 0000000002000000 1
07:    boot 0000000002000000 1
08: system 0000000040000000 1
09:    cache 0000000030000000 2
10:    data ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
[mmc_get_partition_table] skip conf partition.
[mmc_get_partition_table] skip cache partition.
Partition table get from SPL is :
      name                      offset             size             flag
===================================================================================
0: bootloader                      0          400000                0
1: reserved                   2400000          4000000                0
2: conf                      6c00000          400000                1
3: cache                      7800000       30000000                2
4: env                      38000000          800000                0
5: logo                      39000000          2000000                1
6: recovery                   3b800000          2000000                1
7: rsv                      3e000000          800000                1
8: tee                      3f000000          800000                1
9: crypt                      40000000          2000000                1
  10: misc                      42800000          2000000                1
  11: boot                      45000000          2000000                1
  12: system                   47800000       40000000                1
  13: data                      88000000       14a000000                4
mmc read lba=0x12000, blocks=0x1
mmc read lba=0x12001, blocks=0x1
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x38000000
serial
serial
serial
board id is : 8
___39 > do_get_rebootmode reboot_mode(0xc810023c)=0x0
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 7, table = 1
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
   Amlogic multi-dtb tool
   Multi dtb detected
   unified board, board id = 8
CONFIG_4LAYERS_BOARD_ID_1  8  12 size: 0x40000000,
   Multi dtb tool version: v2 .
   Support 7 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxb plat: p200 vari: 1g
      dtb 1 soc: gxb plat: p200 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
      dtb 6 soc: gxl plat: p215hc100 vari: 2g
   Find match dtb: 2
dwmac.c9410000
zteDbg: original preboot=run init_display;run storeargs;run irremote_update;run switch_bootmode;
zteDbg: current preboot=run init_display;run storeargs;run irremote_update;run switch_bootmode;
[CANVAS]addr=0x3d800000 width=5760, height=2160
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
key1 = 7b84c43b
key2 = b748ff00
key3 = 6699dd22
key4 = 66994eb1
key5 = 66994db2
key6 = 66994cb3
time_out = 30d40
ir init
irkey - irkey key_value1 key_value2 key_value3 key_value4 key_value5 key_value6 time_value
Usage:
irkey
___39 > do_get_rebootmode reboot_mode(0xc810023c)=0x0
Try USB burn
ztebsp: bootcmd=jpeg ${outputmode};bootsys
[setup_bootenv] COMControlFlag=> value[1]=0, val=0
Saving Environment to aml-storage...
mmc env offset: 0x38000000
Writing to MMC(1)... not found mac in efuse
zte_mac=28:8C:B8:36:29:50,ethaddr=28:8C:B8:36:29:50
Hit any key to stop autoboot:  0
Starting logo
[Logo_disp]: ====== Logo_disp ======
[draw_logo] size=0xa72c8, ntohl(imgheader.len)=0xa7268, ntohs(imgheader.offset)=0x60
[draw_logo] after ALIGN, size=0xa7400
[draw_logo]: before read_logo_data
[draw_logo]: draw_logo 1481
[draw_logo]: draw_logo 1483
[set_logoParam]: enter the set_logoParam
[set_logoParam]:  Id          FileName             Type          No    Addr                   Size
[set_logoParam]: before the get_logo_source PAL_LOGO_PICTURE
### get_logo_source: material.type=0, material.No=1
[set_logoParam]:  <0>          LogoPic(480i)          0             1    0x11000288             151757
### get_logo_source: material.type=0, material.No=1
### get_logo_source: material.type=0, material.No=2
[set_logoParam]:  <1>          LogoPic(576i)          0             2    0x11025358             151757
### get_logo_source: material.type=0, material.No=1
### get_logo_source: material.type=0, material.No=2
### get_logo_source: material.type=0, material.No=3
[set_logoParam]:  <2>          LogoPic(720p)          0             3    0x1104a428             151757
### get_logo_source: material.type=0, material.No=1
### get_logo_source: material.type=0, material.No=2
### get_logo_source: material.type=0, material.No=3
### get_logo_source: material.type=0, material.No=4
[set_logoParam]:  <3>          LogoPic(1080i_p)       0             2    0x1106f4f8             151757
[draw_logo]: draw_logo 1526
before the  decompressToRGB
Start to decode the LOGO jpeg ...
[decompressToRGB]: before the decompress_jpeg_rgb
[decompressToRGB]: Call decompress_pic_rgb565(id=3,addr=1106f4f8,size=151757,maxw=1920,maxh=1080,Bpp=3) ...
[decompressToRGB]: after the decompress_jpeg_rgb
[draw_logo]: Success in decoding LOGO src file: (w=1920,h=1080,Bpp=3,data=0x3bf46910)
[deinit_Logo]: all LOGO's resource (Exc. logoThread) are released
Logo_disp ret: 0
read boot-recovery from misc failed.
ztebsp: ethaddr=28:8C:B8:36:29:50
[setup_bootenv] ScreenMode=> value[7]=1, val=1
[setup_bootenv] COMControlFlag=> value[8]=FA100499007037300000288CB8362950, val=0
Saving Environment to aml-storage...
mmc env offset: 0x38000000
Writing to MMC(1)... not found mac in efuse
set osd_size 720p
bootmode:NORM
ztebsp: head magic=55667788
ztebsp: cmdT = imgread kernel boot ${loadaddr}; store dtb read ${dtb_mem_addr}; bootm ${loadaddr}
bootargs=rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 use_cma_first=1 androidboot.selinux=disabled logo=osd1,loaded,0x3d800000,576cvbs vout=576cvbs,enable hdmimode=1080p50hz cvbsmode=576cvbs hdmitx= cvbsdrv=1 androidboot.firstboot=1 jtag=apee quiet androidboot.hardware=amlogic androidboot.boardid=8 osd_size=720p mac=28:8C:B8:36:29:50 system=norm runlevel=0 boot_revision=V810558 boardtype=8 quiet COMControlFlag=0 uimode=720p productid=FA100499007037300000288CB8362950 bootvideo=0 market=32,1 ir_recovery=0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
   Amlogic multi-dtb tool
   Multi dtb detected
   unified board, board id = 8
CONFIG_4LAYERS_BOARD_ID_1  8  12 size: 0x40000000,
   Multi dtb tool version: v2 .
   Support 7 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxb plat: p200 vari: 1g
      dtb 1 soc: gxb plat: p200 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
      dtb 6 soc: gxl plat: p215hc100 vari: 2g
   Find match dtb: 2
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =3bf46910
copy done
use dts in boot.img/recovery.img instead of dts partition.
   Amlogic multi-dtb tool
   Multi dtb detected
   unified board, board id = 8
CONFIG_4LAYERS_BOARD_ID_1  8  12 size: 0x40000000,
   Multi dtb tool version: v2 .
   Support 7 dtbs.
      aml_dt soc: gxl platform: p211 variant: 1g
      dtb 0 soc: gxb plat: p200 vari: 1g
      dtb 1 soc: gxb plat: p200 vari: 2g
      dtb 2 soc: gxl plat: p211 vari: 1g
      dtb 3 soc: gxl plat: p211 vari: 2g
      dtb 4 soc: gxl plat: p215 vari: 1g
      dtb 5 soc: gxl plat: p215 vari: 2g
      dtb 6 soc: gxl plat: p215hc100 vari: 2g
   Find match dtb: 2
L258:
L260:
L266:load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02006b88
Loading Ramdisk to 3bc35000, end 3bebeb0e ... OK
Loading Device Tree to 000000001fff4000, end 000000001ffffe5d ... OK
fdt_instaboot: get header err
Starting kernel ...
uboot time: 3373654 us
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpu
[ 0.000000@0][ 0/swapp] Initializing cgroup subsys cpuacct
[ 0.000000@0][ 0/swapp] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0][ 0/swapp] bootconsole [earlycon0] enabled
get_dvfs_info 0008
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[ 1.[ 17.277183@0][ 5294/Threa] monitor: received netlink message:ztebw ok
[ 17.277995@0][ 5294/Threa] monitor:reply
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

renyyren · 發表于 2018-3-20 22:36

本帖最后由 renyyren 于 2018-3-21 07:55 編輯

來人幫我看看呀

renyyren · 發表于 2018-3-20 22:36

本帖最后由 renyyren 于 2018-3-21 07:55 編輯

.快來人幫我看看呀

李白不喝酒 · 發表于 2018-3-21 09:12

https://n.znds.com/article/24805.html樓主參考一下這個

renyyren · 發表于 2018-3-21 10:07

李白不喝酒發表于 2018-3-21 09:12
https://n.znds.com/article/24805.html樓主參考一下這個

現在不是方法問題，而是跑碼后沒有命令提示符

zhoubo0072003 · 發表于 2018-4-2 13:46

TTL被禁用輸入命令，直接線刷第三方固件

qgbcs · 發表于 2022-8-11 22:15

zhoubo0072003 發表于 2018-4-2 13:46
TTL被禁用輸入命令，直接線刷第三方固件

、最終的解決方案是卡刷，最放心最安全。U盤新建文件夾ZTESTBUSB，把ota.zip拷貝進去，開機不斷地按方向左，進入recovery，選擇u盤更新即可。

› 運營商IPTV / 有線電視 / 廣電機頂盒 › 中興機頂盒

中興B860AV1.1-T接CH340G小板連ttl遇到的問題 ...

中興B860AV1.1-T接CH340G小板連ttl遇到的問題

相關帖子