首頁 收藏 QQ群
 網站導航

ZNDS智能電視網 推薦當貝市場

TV應用下載 / 資源分享區

軟件下載 | 游戲 | 討論 | 電視計算器

綜合交流 / 評測 / 活動區

交流區 | 測硬件 | 網站活動 | Z幣中心

新手入門 / 進階 / 社區互助

新手 | 你問我答 | 免費刷機救磚 | ROM固件

查看: 6587|回復: 9
上一主題 下一主題
[求助]

6108V9卡在logo,變磚,求助大神看看

[復制鏈接]
跳轉到指定樓層
樓主
發表于 2024-6-6 14:11 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式 | 來自江蘇
華為機頂盒卡在logo了,燒錄幾次還是這樣。是1+8G的6108v9***********************
MMC/SD controller initialization.
MMC/SD Card:
    MID:         0x90
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7456M Bytes (High Capacity)
    Name:        "H8G4a"
    Chip Type:   MMC
    Version:     4.0
    Speed:       52000000Hz
    Bus Width:   8bit
    Boot Addr:   0 Bytes

Boot Env on eMMC
    Env Offset:          0x00100000
    Env Size:            0x00010000
    Env Range:           0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked


SDK Version: HiSTBAndroidV600R001C00SPC063_v2016022921

get key value  0x0
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 3072
HI_Flash_Read Ret= 10485760
HI_Flash_Read Ret= 10485760
******** boot from kernel...********
bootargs = coherent_pool=2M console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),4M(bootargs),16M(recovery),1M(deviceinfo),4M(baseparam),4M(pqparam),4M(logo),16M(fastplay),8M(misc),24M(factory),12M(kernel),8M(iptv_data),340M(backup),340M(cache),520M(system),-(userdata)HI_Flash_Read Ret= 512
HI_Flash_Read Ret= 512
Stb mac is : [50:01:6B:47:19:10]

Reserve Memory
    Start Addr:          0x3FFFE000
    Bound Addr:          0x8D3D000
    Free  Addr:          0x3ED48000
    Alloc Block:  Addr        Size
                  0x3FBFD000       4194304
                  0x3F8FC000       3145728
                  0x3F87B000       524288
                  0x3F878000       8192
                  0x3F843000       212992
                  0x3F742000       1048576
                  0x3F73E000       12288
                  0x3F3B9000       3686400
                  0x3F223000       1658880
                  0x3EE9E000       3686400
                  0x3ED4B000       1384448
                  0x3ED48000       8192

Press Ctrl+C to stop autoboot

kernel  @ 3e08000 (7836720 bytes)
ramdisk @ 4e00000 (329180 bytes)
page size @ 2048 bytes
initrd rd_start = 4e00000,rd_end = 4e505dc
## Booting kernel from Legacy Image at 01ffc7c0 ...
   Image Name:   Linux-3.10.0_s40
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    7836656 Bytes = 7.5 MiB
   Load Address: 02000000
   Entry Point:  02000000
load:2000000,blob_start:1ffc7c0,blob_end:2775bf0,image_start:1ffc800,image_len:7793f0
   Loading Kernel Image ... OK
OK
   kernel loaded at 0x02000000, end = 0x027793f0
images.os.start = 0x1FFC7C0, images.os.end = 0x2775bf0
images.os.load = 0x2000000, load_end = 0x27793f0
ret -2
initrd rd_start = 4e00000,rd_end = 4e505dc

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.0_s40 (root@HW-TV-S3) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #1 SMP Mon May 23 12:23:40 CST 2016
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: bigfish
cma: CMA: reserved 400 MiB at 25c00000
cma: CMA: reserved 4 MiB at 3fc00000
Memory policy: ECC disabled, Data cache writealloc
CPU: Hi3798Mv100
PERCPU: Embedded 8 pages/cpu @81a8a000 s12224 r8192 d12352 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260096
Kernel command line: coherent_pool=2M console=ttyAMA0,115200 blkdevparts=mmcblk0:1M(fastboot),4M(bootargs),16M(recovery),1M(deviceinfo),4M(baseparam),4M(pqparam),4M(logo),16M(fastplay),8M(misc),24M(factory),12M(kernel),8M(iptv_data),340M(backup),340M(cache),520M(system),-(userdata) mem=1G mmz=ddr,0,0,400M
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1024MB = 1024MB total
Memory: 599892k/599892k available, 448684K reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xc0800000 - 0xff000000   (1000 MB)
    lowmem  : 0x80000000 - 0xc0000000   (1024 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .text : 0x80008000 - 0x80ee3fa0   (15216 kB)
      .init : 0x80ee4000 - 0x80f54fc0   ( 452 kB)
      .data : 0x80f56000 - 0x8109d0c8   (1309 kB)
       .bss : 0x8109d0c8 - 0x8128349c   (1945 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:192
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
Console: colour dummy device 80x30
Calibrating delay loop... 1949.69 BogoMIPS (lpj=974848)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 33110 entries in 98 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80b27ea8 - 0x80b27f00
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (7829.50 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
[111 ERROR-Invalid]:MCE_Init[2135]:ERR: get PDM Param
NET: Registered protocol family 16
DMA: preallocated 2048 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0xf8b00000 (irq = 81) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0xf8006000 (irq = 82) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0xf8b02000 (irq = 83) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource timer3
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 320K (84e00000 - 84e50000)
NetWinder Floating Point Emulator V0.97 (double precision)
CPU PMU: probing PMU on CPU 0
hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 1980
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
input: Hi keyboard as /devices/virtual/input/input0
input: Hi mouse as /devices/virtual/input/input1
input: qwerty as /devices/virtual/input/input2
Hi Android vinput driver init successful!
Found Nand Flash Controller V610.
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
libphy: himii: probed
Up port phy at 0x01 is connect
libphy: PHY himii:1f not found
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbotg: usb otg driver registeredusbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
dwc_otg: version 3.00a 10-AUG-2012
Core Release: 3.10a
Setting default values for core params

WARN::dwc_otg_core_reset:5176: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001

WARN::dwc_otg_core_reset:5176: dwc_otg_core_reset() HANG! Soft Reset GRSTCTL=80000001

Using Buffer DMA mode



上一篇:魔百盒M411A S905L3A-B 晶晨S905L3A/L3AB芯片通刷_原生ATV9線刷包...
下一篇:華為悅盒EC6109開啟IPv6方法大揭秘!小白也能輕松搞定!
沙發
發表于 2024-6-6 14:28 | 只看該作者 | 來自廣東
是不是刷機固件不匹配啊
回復 支持 反對

使用道具 舉報

板凳
發表于 2024-6-6 15:11 | 只看該作者 | 來自四川
這是非高安的機子,要用非高安的固件升級。
回復 支持 反對

使用道具 舉報

地板
發表于 2024-6-6 15:46 | 只看該作者 | 來自四川
Using Buffer DMA mode
可以放棄治療了
回復 支持 反對

使用道具 舉報

5#
 樓主| 發表于 2024-6-11 12:41 | 只看該作者 | 來自江蘇
放棄了
回復 支持 反對

使用道具 舉報

6#
發表于 2024-6-11 13:30 | 只看該作者 | 來自安徽
我有備份
回復 支持 反對

使用道具 舉報

7#
發表于 2024-6-11 13:30 | 只看該作者 | 來自安徽
回復 支持 反對

使用道具 舉報

8#
 樓主| 發表于 2024-6-12 13:30 | 只看該作者 | 來自江蘇
謝謝啦!怎么給備份我?
回復 支持 反對

使用道具 舉報

9#
發表于 2024-6-13 07:54 來自ZNDS手機版 | 只看該作者 | 來自四川
強刷就能救
回復 支持 反對

使用道具 舉報

10#
 樓主| 發表于 2024-6-14 16:18 | 只看該作者 | 來自江蘇
用海兔燒錄過好多次,各種版本。還是不行。強刷是什么短接J16、插U盤都不行沒反應。
回復 支持 反對

使用道具 舉報

您需要登錄后才可以回帖 登錄 | 立即注冊

本版積分規則

Archiver|新帖|標簽|軟件|Sitemap|ZNDS智能電視網 ( 蘇ICP備2023012627號 )

網絡信息服務信用承諾書 | 增值電信業務經營許可證:蘇B2-20221768 丨 蘇公網安備 32011402011373號

GMT+8, 2024-11-14 01:39 , Processed in 0.075191 second(s), 15 queries , Redis On.

Powered by Discuz!

監督舉報:report#znds.com (請將#替換為@)

© 2007-2024 ZNDS.Com

快速回復 返回頂部 返回列表