咪咕mgv2000 九聯南傳，跑碼后顯示如下，就不動了
GXLX:BL1:9ac50e:4a8da0;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 102948
BL2 Built : 19:16:55, Jun 22 2018.
gxl gb679ae5 - yao.zhang@droid07
Board ID = 3, adc=225
GET GPIO_AO_4 VALUE:16-------
set gpio_ao_4 high
CPU clk: 1200MHz
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 1c 02 36 31 13 4f 1a 00 35 35 19 52 19 00 32 35 17 53 21 02 40 33 13 54 717 - PASS
Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
emmc 52M
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00047200
NOTICE: BL3-1: v1.0(debug):521e8c3
NOTICE: BL3-1: Built : 14:22:49, Jun 5 2018
NOTICE: BL31: GXL normal boot!
NOTICE: BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-27cb61a 2018-07-11 13:57:47 xianghua.tan@droid12-sz]
efuse init ops = c1
efuse init hdcp = c, cf9=7
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 4c b6 38 a0 0 c1 not ES chip
[0.538648 Inits done]
sINFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
tarre task s
! t
5hi-gBh tasoko ts t2a0rt1!
9.0lo1w (tMaasrk 2s6t a2r0t1!
- 19:30:56)
DRAM: 1 GiB
Relocation Offset is: 36eef000
gpio: pin GPIODV_24 (gpio 43) value is 1
register usb cfg[0][1] = 0000000037f61708
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
dtb magic 5f4c4d41
Amlogic multi-dtb tool
Multi dtb detected
unified board, board id = 43
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx platform: p261 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 1
start dts,buffer=0000000033ee4610,dt_addr=0000000033eee610
Amlogic multi-dtb tool
Multi dtb detected
unified board, board id = 43
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx platform: p261 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 1
parts: 12
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: boot 0000000002000000 1
07: system 0000000040000000 1
08: cache 0000000020000000 2
09: params 0000000004000000 2
10: bootfiles 0000000020000000 2
11: data ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 43
hpd_state=0
cvbs performance type = 7, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc ebc74ff1, store ebc74ff1
_verify_dtb_checksum()-924: calc ebc74ff1, store ebc74ff1
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx platform: p261 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 1
wipe_data=successfulSecd
wipe_cache=successful
bmp pixel: 24
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=5760, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[keymanage_dts_get_key_device]L85:model key name is not exist
[KM]Error:f[_get_km_ops_by_name]L231:key model not know device 4
[KM]Error:f[key_manage_query_exist]L546:There isn't dts cfg for key[model]
[KM]Error:f[key_manage_query_size]L503:Fail in query key exist
boot_select kernel[0,3) recovery[3,10) factory[10,*)
boot_select current count=0
boot_select count=0
boot_select=kernel
rebootmode=cold_boot
Hit any key to stop autoboot: 0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33efb970
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02058110
Loading Ramdisk to 33dff000, end 33edca9e ... OK
Loading Device Tree to 000000000fff3000, end 000000000ffff84f ... OK
fdt_instaboot: get header err
Starting kernel ...
uboot time: 1988089 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29 (umMTestOne@ubuntu) (gcc version 4.9.2 20 140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-201 4.09) ) #1 SMP PREEMPT Mon Apr 1 16:27:51 HKT 2019
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 002b
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
root@p201_iptv:/ # SMI_RAC_TDAT16M30S.sh Start read mmcblk0....
|
網站導航
樓主: killery23
[復制鏈接]
發表于 2019-10-22 09:19
znds.com 