求救磚付費江蘇移動創維E900V21C

jiyong123 · 發表于 2017-12-21 12:08

本帖最后由 jiyong123 于 2017-12-21 12:17 編輯

      @hao501802766
      前兩天剛剛把刷機心得（2017年12月江蘇移動創維E900V21C刷機成功）和大家分享了。由于徹底關機后再開機，WIFI需要手動連接，覺得是固件版本的問題，昨晚重新試了《樂天20170828版-卡刷包》，刷完盒子重啟，盒子就再也沒亮起來了，電視直接什么圖像都沒有。
   換了2臺電腦，3條USB線， 2條TTL線（CH341線，PL2303線）

故障現象：
1、通電后，主板上PWR主電源燈亮一下綠燈就變紅了；LAN網口燈一直紅燈；IR遙控燈一直是熄滅狀態。
2、刷機軟件USB_Burning_Tool，一直發現不了盒子，且反復開關都不識別。
3、TTL跑到一半就卡住了，怎么回車都沒反應，試了很多次。
Starting kernel ...
uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

4、TTL完整信息在2樓
求救磚付費江蘇移動創維E900V21C

jiyong123 · 發表于 2017-12-21 12:09

GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

BL2 Built : 18:58:24, Oct 25 2016.
gxl gc9db010 - xiaobo.gu@droid05

set vcck to 1080 mv
set vddee to 1050 mv
Board ID = 2, adc=153
CPU clk: 1200MHz
2layers board, use ddr_set[0]
DDR chl: Rank0+1 @ 720MHz - FAIL
DDR chl: Rank0 @ 720MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x00007400
Load bl301 from eMMC, src: 0x00018200, des: 0x01200000, size: 0x00002000
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000a6200
NOTICE:  BL3-1: v1.0(debug):959fdf0
NOTICE:  BL3-1: Built : 15:01:44, Dec 29 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3086-872dec0 2016-09-21 21:56:30 xiaobo.gu@droid05]
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: ef be ad de d f0 ad ba ef be ad de not ES chip
efuse init ops = c2
efuse init hdcp = c, cf9=7
[0.414842 Inits done]
seINFcOu:r e t aBsLk3 -s1t:a rItn!it
ializing runhtiigmhe  tsaesvices
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-svn125577 (Mar 18 2017 - 21:47:22)

DRAM:  1 GiB
Relocation Offset is: 36ecf000
gpio: pin GPIODV_24 (gpio 43) value is 0
gpio: pin GPIOAO_3 (gpio 103) value is 1
mwm 0xc8837004:[0x aa203] with [0x ea203] ok
mwm 0xc883700c:[0x 3e3b744] with [0x 3e3b764] ok
mwm 0xc8837010:[0x c0101] with [0x c8101] ok
mwm 0xc8837010:[0x c8101] with [0x  128101] ok
register usb cfg[0][1] = 0000000037f63db0
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC: aml_priv->desc_buf = 0x0000000033ebfdb0
aml_priv->desc_buf = 0x0000000033ec20d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
[mmc_startup] mmc refix success
[mmc_init] mmc init success
overide_emmc_partition_table: overide cache
[mmc_get_partition_table] skip partition cache.
mmc read lba=0x12000, blocks=0x2
mmc read lba=0x12002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 2
hpd_state=1
[720p50hz] is invalid for cvbs.
set hdmitx VIC = 19
config HPLL = 2972
HPLL: 0xc000027b
config HPLL done
j = 2  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 19
enc_vpu_bridge_reset[1189]
rx version is 1.4 or below  div=10
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
dwmac.c9410000
Error: dwmac.c9410000 address not set.

wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode=cold_boot
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
[OSD]ERR: 24 bit/pixel mode, but BMP has 16 bit/pixel
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
amlkey_issecure() 138: ret 1
amlkey_size() 162: ret 1
[KM]Error:f[key_unify_read]L301:key[mac] not programed yet
[KM]Error:f[do_sec_keyunify]L682:mac key read fail
don't use random mac produce in uboot
IR init done!
gpio: pin GPIOH_6 (gpio 55) value is 1
Hit any key to stop autoboot:  0
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f44bc0
copy done
   Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x02033200
Loading Ramdisk to 33c36000, end 33ebca00 ... OK
Loading Device Tree to 000000001fff3000, end 000000001ffff3a1 ... OK

Starting kernel ...

uboot time: 2041271 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-svn125577 (chenshouhui@ubuntu) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Sat Mar 18 22:16:52 HKT 2017
[ 0.000000@0] CPU: armv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0

hao501802766 · 發表于 2017-12-21 12:39

jiyong123 發表于 2017-12-21 12:09
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 101949

用雙頭USB 重刷這個包：http://ktgpgw.cn/rom/20132.html

jiyong123 · 發表于 2017-12-21 12:44

hao501802766 發表于 2017-12-21 12:39
用雙頭USB 重刷這個包：http://ktgpgw.cn/rom/20132.html

雙頭的線換了好幾條了
刷機軟件一直識別不到盒子

hao501802766 · 發表于 2017-12-21 12:45

jiyong123 發表于 2017-12-21 12:44
雙頭的線換了好幾條了
刷機軟件一直識別不到盒子

盒子接通電源開機然后馬上插入USB 應該可以我是這樣刷機操作基本都OK

jiyong123 · 發表于 2017-12-21 13:05

我都是關機，插上USB，再插電源，不行！
按你的方法連續測試了20次還是不行！
軟件發現不了盒子

hao501802766 · 發表于 2017-12-21 13:55

那我也沒好的辦法了要么就選擇寄過來我試試看當然也不保證一定能弄好

jiyong123 · 發表于 2017-12-21 14:04

hao501802766 發表于 2017-12-21 13:55
那我也沒好的辦法了要么就選擇寄過來我試試看當然也不保證一定能弄好 ...

可以的江浙滬范圍發給你們很方便的

jiyong123 · 發表于 2017-12-21 16:07

hao501802766 發表于 2017-12-21 13:55
那我也沒好的辦法了要么就選擇寄過來我試試看當然也不保證一定能弄好 ...

地址已收到，沒權限發短消息。這里回復，明天發快遞出去

jiyong123 · 發表于 2017-12-24 20:01

@hao501802766
快遞已發 申通402886040185

› 你問我答 / 玩機教程 / 固件 › ZNDS刷機/救磚